







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Fort Worth Homeowners Choose Toto Construction
Rowan Construction Group Fort Worth provides independent Toto service and construction in Fort Worth: Washlet diagnosis and repair, Drake and Ultramax valve work, and full bathroom remodels built around Toto fixtures. We’re not affiliated with or authorized by Toto. We’re an independent Toto service provider that reads the spec sheets, keeps the parts diagrams on hand, and quotes the number in writing before anyone touches the fixture. Our technicians have up to 19 years of experience, and the bath work on this page covers full remodels, tile and fixtures, and small bathroom jobs across Fort Worth. Call (833) 570-6084 for a free estimate.
Why Trust Rowan Construction Group Fort Worth for Your Toto Construction?

Because we’re independent, we track Toto’s actual rough-in dimensions, parts diagrams, and spec sheets across the Washlet, Drake, and Ultramax lines instead of selling whatever a manufacturer rep is pushing that quarter. That matters when your Drake needs a specific flush valve gasket and not a generic one-size kit. Our technicians have up to 19 years of experience working with Toto’s proprietary internals: the 3-inch flush valve in the CST743 and CST744, the tank-to-bowl joint on the Ultramax II one-piece, the electronics inside a C5 or S550e seat.
We source OEM-compatible Toto parts when a failure is component-level, because aftermarket parts for these proprietary systems cause repeat failures we then have to answer for. Every Fort Worth job starts with a written flat price and a written scope before any work begins, and no change proceeds without a signed change order. That’s Clause 1 of the Haven Standard, and it’s the reason our projects finish within a few percent of the number the customer agreed to. You also get a documented photo record on every visit, included as standard.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in Fort Worth
- Washlet seat failures from hard water. Fort Worth’s water runs mineral-heavy, so the Washlet C5 and S550e wand nozzles clog with scale and the inlet screens restrict flow until the unit faults out or stops spraying. Left alone, the heating element scales too, and a seat that once warmed in seconds now takes a minute or dies entirely.
- Drake flush valve and fill valve wear. The 3-inch flush valve gasket and the fill valve diaphragm on a CST743 or CST744 degrade over time. The classic sign is phantom running: the toilet keeps trickling long after the flush, or the flush gets weak. It’s one of the most common Toto calls we get across Fort Worth slab homes.
- Ultramax one-piece tank-to-bowl leaks. On the MS604114CEFG, the tank-to-bowl gasket and bolts at the joint can seep slowly. Homeowners rarely see the water; they see a warped vinyl floor or soft subfloor near the flange months later. Expansive clay soils and slab movement can worsen how a leak reads through the floor.
- Electronic bidet control board and moisture intrusion. The seat hinge is where moisture gets in, and North Texas humidity swings plus undersized bathroom venting speed that up. A board that’s seen damp starts ghosting, dropping remote pairing, or refusing to heat.
- EcoPower and EcoFlush performance complaints. High-efficiency Toto lines can underperform when supply pressure is low or a fill valve is set wrong. The toilet isn’t failing; the setup is. We test fill and flush volume at the fixture rather than guessing.
Toto Parts & Our Repair-vs-Replace Approach

We source OEM Toto fill valves, flush valve gaskets, tank-to-bowl seals, and Washlet inlet screens and nozzles whenever a failure is component-level. Aftermarket parts for Toto’s proprietary flush systems and electronics frequently cause repeat failures, and a second visit costs more than the right part the first time. We don’t claim to stock Toto parts locally; we identify the part your fixture needs and source it for the job.
When a Washlet control board has failed out of warranty, or a one-piece tank shell has cracked, we give an honest replace recommendation rather than patching a part that will fail again. The math only favors repair on trim, valve, and seal work. Every recommendation comes with a written flat price and a written scope before work starts, and a free second opinion on any written estimate if you want our read on a competitor’s quote. Call (833) 570-6084 and we’ll price the repair or the replacement so you can compare.
Our Toto Service Process – Step by Step
- 1
Diagnosis. A typical Toto job starts when a homeowner notices a Washlet seat that no longer heats or sprays weakly, or a Drake that runs intermittently. We pull the seat, check the inlet screen and nozzle assembly for mineral scale, verify voltage at the control board, then inspect the flush valve gasket and fill valve. A washlet that’s fine and a tank that isn’t are two separate line items.
- 2
Written price and scope. You get a flat price with the exact parts and labor listed before anyone starts. No “call for a quote.”
- 3
Repair or install. The usual fix is nozzle and screen cleaning or replacement, a flush valve gasket and fill valve swap, and a fresh wax seal if the flange shows any seepage. For remodels, we set the rough-in to Toto’s spec so the fixture seats clean.
- 4
Test. We check flush volume, fill level, seat spray pattern, and heat at the fixture. You see the test, not just the invoice.
- 5
Warranty and record. A written workmanship warranty under the 365-Day Done Right Promise, plus a documented photo record of what we found and what we did.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in Fort Worth
We work across the Toto lines you’re most likely to have in a Fort Worth bathroom: the Drake two-piece elongated in the CST743 and CST744 families, the Ultramax II one-piece MS604114CEFG, the Washlet C5 and S550e electronic bidet seats, and the EcoPower and EcoFlush high-efficiency toilet lines. We also handle the broader bath work around them: full remodels, tile and fixtures, and small bathroom remodels where a Toto fixture is part of the plan. If you’re updating a Fairmount bungalow or a newer west-side build, we set the fixture to spec and thread the work through whatever the historic district or current code requires.
We Also Service These Brands
Toto is one of more than fifty vetted brands we work with. We also service KraftMaid cabinetry, Kohler fixtures, GAF roofing, and PGT windows and doors across Fort Worth. That range gives your written quote honest numbers instead of inflated ones, and it means we’ll tell you when a non-Toto part is the better call for a given fixture. Call (833) 570-6084 for a free estimate on any of them.
FAQs – Toto Construction Service in Fort Worth

Is Rowan Construction Group Fort Worth authorized by Toto? No. We’re an independent Toto service provider, not affiliated with or authorized by Toto. We work on Toto fixtures because we know them, using our own sourced OEM-compatible parts. Call (833) 570-6084 with questions.
Do you use genuine Toto/OEM parts? Yes, on component-level failures. We source OEM Toto fill valves, flush valve gaskets, tank-to-bowl seals, and Washlet inlet screens and nozzles because aftermarket parts for these proprietary systems tend to fail again. Call (833) 570-6084 for a written quote.
How much does Toto construction cost in Fort Worth? A component repair like a flush valve or fill valve swap runs well under a full bathroom remodel, while a Toto-centered bathroom remodel in Fort Worth runs $9000 – $28000. Small bathroom remodels land at $5000 – $12000. Call (833) 570-6084 for an exact quote, and estimates are free.
What Toto models/series do you cover? The Drake CST743 and CST744, the Ultramax II MS604114CEFG, the Washlet C5 and S550e, and the EcoPower and EcoFlush lines, plus tile and fixture work around any of them. Call (833) 570-6084 to confirm your model.
Will service void my Toto warranty? No, as long as the work is done correctly with compatible parts. Our warranty-safe practices keep the fixture within Toto’s specs. Call (833) 570-6084 and we’ll walk you through what your warranty covers.
Can you install a Toto Washlet on an existing non-Toto toilet in my Fort Worth home? Usually yes. Most standard elongated and round-front toilets accept a Washlet seat with the right T-adapter and a nearby outlet. We check your rough-in and outlet placement first, then quote it flat. Call (833) 570-6084 to schedule an assessment.
Book Your Toto Service in Fort Worth, TX
Whether it’s a Washlet that stopped spraying, a Drake that won’t stop running, or a full Toto-centered bath remodel, Fort Worth jobs start with a free estimate and a written price before work begins. Call (833) 570-6084 to schedule yours.
| Service | Fort Worth Price Range |
|---|---|
| Bathroom Remodel | $9000 – $28000 |
| Small Bathroom Remodel | $5000 – $12000 |
| Walk-In Shower Installation | $4500 – $12000 |
| Tub-to-Shower Conversion | $3500 – $10000 |
| Bathroom Vanity Installation | $800 – $3000 |
Written by the team at Rowan Construction Group Fort Worth.












